Can You Hook Up A Turntable Directly To Speakers?

What speakers are compatible with Audio Technica turntable?

5 Powered Speakers for Audio Technica AT-LP60 and AT-LP120 TurntablesThe Easiest Turntable Setup.Receiver vs Powered Speakers.Powered Speakers Comparison.Logitech Speaker System Z323 with Subwoofer.Alesis M1 Active 320 USB.M-Audio Studiophile AV 30 and AV 40.Mackie CR3 Multimedia Monitors.More items…•.

How far should speakers be from turntable?

How far apart? This depends on the size of your speakers, the distance to your listening position and the size of the room, but a good place to start is two metres (or a slightly less snappy, 6.56ft if you’re doing this in Imperial).

How do you hook up old turntable to speakers?

To use a vintage turntable with these newer units or to play through a computer, powered speakers or headphones, the turntable signal must pass through an external phono preamp. You’ll then plug the output from the phono preamp into line-level inputs on your gear (these may be marked Aux, Tape, Line, Video, CD, etc).

Can you connect a turntable to AUX?

If your receiver does not have a phono input, don’t worry – many turntables have their own built-in preamp. (You can verify this in the owner’s manual.) As long as this is the case, you can use any receiver input, such as the ones labeled “Line,” “Audio,” “CD” or “Auxiliary.”

Can I use a turntable without an amp?

Yes. A turntable must be connected to an amplifier as the output signal is not strong enough to drive speakers. However, there is an exception as a lot of record players have pre-amplifiers built-in already.

Can I use aux input for phono?

Short answer: NO. Phono output is typically 2.5mV and AUX is 1V; so you can plug it into the phono input but even at full volume you’ll barely get any sound. …. and that’s the truth.

Why do you need a preamp for a turntable?

A turntable MUST NOT connect to an input labelled as “AUX”, “TAPE”, “CD, or “TUNER.” This is because the phono cartridge signal must be amplified and equalised in a unique manner by a device known as a phono preamp.

Do I need a receiver for my record player?

A standard turntable requires a few things to operate: the turntable itself, a preamplifier, an amplifier, and speakers, in addition to all of the cables and wires that are needed to connect these components together. Receivers have built-in amps. Some models (especially older ones) also have built-in preamps.

Do you need speakers with a turntable?

Turntables don’t come with speakers built-in. So they need to be hooked up to speakers to play records. The speakers can be powered and have the amplifier built-in. Or you can use passive speakers and a separate amplifier.

Can you connect a turntable to a soundbar?

If the only audio system you’ve got is a soundbar or soundbase connected to your TV, you might be tempted to assume that adding a turntable simply isn’t on the cards – but you’d be wrong. … That means you can add any turntable that has a phono stage built-in, or any standard turntable via an external phono stage.

How do I connect a turntable to a receiver without phono input?

How to Connect a Turntable to a Receiver Without a Phono InputStep 1: Turn Power Off. Turn power off to your receiver, turntable and preamp. … Step 2: Connect Turntable to Preamp. Connect the two output audio cables coming from the turntable to the preamp’s inputs. … Step 3: Connect Preamp to Receiver. … Step 4: Ground Turntable to Preamp. … Step 5: Turn Power On.

What’s the difference between a record player and a turntable?

In its basest form, a turntable is simply a major component of a record player. It is the part of the player that holds the record and spins it. … In this sense of the word, a turntable is similar to a record player, except it does not come with built-in speakers or an amplifier.

What kind of speakers do you need for a turntable?

You will need some kind of speakers to play the music from your turntable. Your main choices are passive or powered speakers. Passive speakers do not have their own built-in amplifier and are powered by a separate amp such as an A/V receiver. These speakers are connected via speaker wire to the amplifier.

What happens if you don’t ground a turntable?

This particular Ground is not a safety issue, it’s there to avoid a Ground Loop. If you have inter-connected equipment, of any kind, with more than one electrical path to the Ground, a Ground Loop can ultimately cause extra noise. … A turntable suffering from a Ground Loop will produce a hum through your speakers.

Can I connect a record player to my TV?

You can connect powered speakers to the turntable. You can try to connect it to your TV using the audio connection of an unused input. The TV may not work without video as well so you could use the video out of another device into the corresponding video connection for the same input.

Do you need a preamp for a turntable?

Some turntables have a preamp built-in. … If your turntable has a USB output, it has a built-in preamp. If you do need an external preamp, you will need a set of cables (usually RCA cables) to connect to your audio system. Preamps have a wide range when it comes to build and sound quality.

What happens if you do not connect the ground wire?

Originally Answered: What happens if a ground wire is not connected? … If there is enough current flow from the device’s damaged wiring, through the ground wire, it will cause either a fuse or circuit breaker to cut off power to the device, preventing further shock hazard.

Do I need a ground wire for my turntable?

Importance of a Ground Wire Ground wires are an important feature on many turntables. A ground wire helps to eliminate unpleasant buzzing, hum or distortion. Referred to by professionals as a “ground loop”, this occurs because the chassis is connected to various components that are not operating at the same voltage.